HUPLONG INDUSTRIES (M) SDN BHD
No 2-48, Jalan Perniagaan 2, Taman Pusat Perniagaan, Kampung Tengah Sungai Abong, 84000 Muar, Johor, Malaysia.
+606-9522968
24B, Jalan PSK 3,
Pusat Perdagangan Seri
Kembangan, 43300
Seri Kembangan,
Selangor, Malaysia.
+6016-3411889
NORRES PROTAPE® TPE 320 (XLD) 每 TPE hose, light
| Previous | 23 / 27 | Next |
- NORRES Granulate and Plastic Dryer Hose Malaysia
- NORRES TPE Hot Air Duct Hose Malaysia
- NORRES UV IR Dryer Air Supply Hose Malaysia
- NORRES PROTAPE TPE 320 XLD Malaysia
- NORRES Hot and Cold Gas Duct Hose Malaysia
Product details
Applications
· flexible hose/ ducting for hot and cold gases and for dust, powder, fibres
· granulate/ plastic dryer, hot air dryer
· film blowing machine, cooling air at the extrusion tool
· air supply: UV dryer, IR dryer
· textile industry, steam soaking: steam iron, industrial ironing machine, smoothing iron
· bus, utility vehicle, caravan/ trailer, mobile home/ camper/ RV, boat, ship/ vessel/ marine, yacht: ventilation, heating
· heating system/ heater: fresh air supply
Properties
· lightweight
· highly flexible + compressible
· very good heat resistance
· good resistance to oil, gasoline and chemicals
· good resistance to alkalis and acids
· conforms to RoHS guideline
· REACH according to --> Technology / Technical Information / REACH
Design
· PROTAPE® tape hose
· 1. spring steel wire integrated in wall
· 2. wall: thermoplastic rubber (TPE)
· 3. wall thickness 0,5 mm approx.
Temperature Range
· -40°C to 125°C
· short time to 150°C
Delivery variants
· further diameters and lengths available on request
· black (standard)
· special colours: full coloured
· customer-specific branding
· ID 1,5''/ 38mm 12/305mm compressed packed in poly bag (low transportation cost / risk, minimum storage size), ID315 500mm not compressed
HUPLONG INDUSTRIES (M) SDN BHD is the authorized distributor of NORRES industrial hoses in Malaysia.
HUPLONG INDUSTRIES (M) SDN BHD supplies genuine NORRES PROTAPE® TPE 320 (XLD) lightweight TPE hoses for flexible ducting of hot and cold gases, dust, powder and fibres.
NORRES PROTAPE® TPE 320 (XLD) is a lightweight TPE hose. NORRES lists this model for flexible hose and ducting applications involving hot and cold gases, dust, powder and fibres.
The official NORRES design is a PROTAPE® tape hose with a spring steel wire integrated in the wall. The hose wall is thermoplastic rubber (TPE) with an approximate wall thickness of 0.5 mm.
NORRES states that PROTAPE® TPE 320 (XLD) is lightweight, highly flexible and compressible, with very good heat resistance. NORRES also lists good resistance to oil, gasoline and chemicals, as well as good resistance to alkalis and acids.
Official NORRES applications include granulate and plastic dryers, hot air dryers, film blowing machines with cooling air at the extrusion tool, air supply for UV dryers and IR dryers, textile-industry steam soaking equipment, ventilation and heating for buses, utility vehicles, caravans, mobile homes, boats, ships and yachts, and fresh-air supply for heating systems and heaters.
The official temperature range is -40°C to 125°C, with short-time operation up to 150°C.
NORRES lists black as the standard delivery variant. Further diameters and lengths, special full-coloured versions and customer-specific branding are available on request according to NORRES.
NORRES states that PROTAPE® TPE 320 (XLD) conforms to the RoHS guideline.
Our team can assist customers throughout Malaysia with NORRES hose selection based on hose diameter, conveyed material, operating temperature, airflow, vacuum condition, installation length and quantity requirement.
The permitted pressure, vacuum and bending-radius values vary by hose size and must be checked against the official technical table before use.
FAQ
Q: What is NORRES PROTAPE® TPE 320 (XLD)?
A: NORRES PROTAPE® TPE 320 (XLD) is a lightweight TPE hose for flexible ducting of hot and cold gases, dust, powder and fibres.
Q: Is PROTAPE® TPE 320 (XLD) an antistatic hose?
A: No antistatic property is stated in the current official NORRES product information for PROTAPE® TPE 320 (XLD). It should not be described as an AS antistatic hose.
Q: What is the official hose construction?
A: NORRES specifies a PROTAPE® tape hose with a spring steel wire integrated in the wall. The wall is thermoplastic rubber (TPE) with an approximate wall thickness of 0.5 mm.
Q: What is the official operating temperature range?
A: NORRES lists an operating temperature range of -40°C to 125°C, with short-time operation up to 150°C.
Q: Can this hose be used for granulate or plastic dryers?
A: Yes. NORRES lists granulate dryers, plastic dryers and hot air dryers among the official applications.
Q: Can PROTAPE® TPE 320 (XLD) be used for film blowing machine cooling air?
A: Yes. NORRES lists film blowing machines with cooling air at the extrusion tool among the official applications.
Q: Is this hose suitable for UV dryer or IR dryer air supply?
A: Yes. NORRES lists air supply for UV dryers and IR dryers among the official applications.
Q: What other applications are officially listed by NORRES?
A: NORRES lists textile-industry steam soaking equipment, ventilation and heating for buses, utility vehicles, caravans, mobile homes, boats, ships and yachts, as well as fresh-air supply for heating systems and heaters.
Q: Is PROTAPE® TPE 320 (XLD) flexible for installation?
A: Yes. NORRES states that this model is highly flexible and compressible.
Q: Is this hose resistant to oil gasoline chemicals alkalis and acids?
A: NORRES lists good resistance to oil, gasoline and chemicals, as well as good resistance to alkalis and acids. Suitability must still be checked against the actual medium, concentration, temperature and operating condition before use.
Q: What colour is the standard NORRES delivery variant?
A: NORRES lists black as the standard delivery variant.
Q: How should the correct hose size be selected?
A: Selection should be based on hose inside diameter, conveyed material, operating temperature, airflow, pressure or vacuum requirement, bending radius, installation length and quantity requirement. The permitted pressure, vacuum and bending-radius values vary by hose size and must be checked against the official technical table before use.